Skip to content
60A MPPT Solar Charge Controller with Li-Ion Battery Low Temp Protection, Parallel…

60A MPPT Solar Charge Controller with Li-Ion Battery Low Temp Protection, Parallel…

    A MPPT Solar Charge Controller with Li-Ion Battery Low Temp Protection, Parallel Charging, and Bluetooth

    HQST MPPT Charge Controller applied Advanced Maximum Power Point Tracking (MPPT) technology to help regulate the power from your solar panel to battery with efficiency no less than 99.5%. This 60 Amp MPPT solar regulator adopts high quality components with maximum conversion efficiency of 98%. The MPPT battery charging can greatly increase the lifetime of your battery and has various unique functions and quite easy to use features.

    Key Features

    Built-in Bluetooth module, you can download the ‘’ChargePro 2.0” (new version) or the PVChargePro” (old version) app for remote monitoring that keeps 300 days of historical data. HQST 48V 60A solar controller is equipped with an LCD screen and LED fault indicators, which can not only check device operating data and status but quickly determine system faults and modify controller parameters.

    HQST 60 Amp MPPT negative grounded controller offers overcharging/over-discharging/overload/overheat/short circuit/reverse protection and Lithium battery low-temperature protection. The maximum degree avoids the damage due to system fault or installation error. The BMS of low temp protection for Li battery automatically identifies low temperature, stops charging Li battery, and protects its life. This function can be switched on and off manually.

    2 HQST MPPT controllers of the same series(M2420N/M2440N/M4860N) can work together to charge the same battery with the parallel charge cable (not included), to meet high power charging requirements and 2 controllers should set the same battery pack voltage. Compatible with Flooded, AGM, Gel, and Lithium batteries. User mode allows the buyer to set their charging parameters. 3-Stage Charging: boost, float, and equalization.

    Die-cast aluminum heat sink makes the heat dissipation efficiency higher, which can minimize the power loss from heat. Filling inside the controller with gel is for better PCBA cooling conduction and prevents water and other damages, extending the controller service life. With the premium IC and better PCBA, this controller can work under full load even at high temperature environment.

    HQST 48V 60A solar charge controller adopts advanced MPPT technology that ensures fast and stable track of of the maximum power point, high tracking efficiency of up to 99%, and peak conversion efficiency of 98%. Maximizing the energy from solar panels to charge your system. Automatically detects 12V, 24V, 36V, or 48V DC system voltages, which is suitable for RVs, Commercial Vehicles, Boats, Yachts, and any off-grid system.

    HQST 60Amp MPPT Solar Charge Controller

    • Battery System Voltage: 12V/24V/36V/48V
    • Rated Solar Charge Current: 60A;
    • Self-consumption: 12mA/12V, 10mA/24V, 5mA/36V, 2mA/48V
    • Max PV Input Voltage: 150V
    • Max PV Input Power: 900W/12V, 1800W/24V, 2600W/36V, 3200W/48V
    • Operating Temperature:.31℉~113℉

    Genasun GV-10-LI-14.2V MPPT Charge Controller For Lithium Batteries

    Free Shipping: Free shipping is only available for orders shipped within the 48 contiguous United States. A shipping fee will be calculated and invoiced on orders shipping outside this area. The shipping fee must be paid before an order ships.

    FOR 14.2V LITHIUM BATTERIES

    The Genasun GV-10 solar charge controller with MPPT for Lithium Batteries is the ultra high-speed MPPT. so effective, it reduces your system cost per watt!

    Genasun controllers are deployed to the most remote locations on earth. They endure years at sea, harsh Antarctic winters, freezing conditions in the upper atmosphere on solar powered airplanes, and in a few off-the-map locations. Made in the USA, each controller is put through complete electrical testing to ensure reliability.

    If you need mission-critical power, this is your controller.

    • Marine-grade/waterproof
    • LED indicator tells you battery state of charge
    • No fans, no relays. longer lasting
    • 98.3% Peak Efficiency
    • Continuous, high-speed MPPT
    • Advanced electronic protections
    • Made in USA
    • 5-Year Warranty

    Super Tiny Night Consumption:

    The Genasun GV-10 burns a scant 0.9mA. This difference in consumption effectively allows the GV-10 to put an extra half an amp-hour into your battery every day, resulting in a critical benefit while waiting out a snow-covered panel or a few bad weeks of clouds

    Radio Silence:

    Most MPPT solar charge controllers broadcast Radio Frequency noise from the DC/DC conversion circuit. Unfiltered inputs and outputs waste energy and interfere with nearby or attached electronics. Genasun worked to eliminated RF emissions from our line of charge controllers.

    ELECTRICAL CHARACTERISTICS:

    Float VoltageRated Battery (Output) CurrentAbsolute Max Voc at STCOperating TemperatureElectrical EfficiencyMPPT Tracking SpeedWeightWarranty
    Model: GV-10-Li-14.2V
    14.2V
    Minimum Battery Voltage for Operation 8.5V
    10.5A
    Nominal Battery Voltage N/A
    34V
    Max Recommended Panel Power 140W
    -40°C to 85°C
    Tracking Efficiency 99% typical
    96%-98% typical
    Night Consumption .9mA
    15 Hz
    Connection 4-position terminal block for 10-30AWG wire
    6.5 oz (185g)
    Dimensions 5.5 x 2.5 x 1.2 (14 x 6.5 x 3.1 cm)
    5 Years

    Custom Field

    Free Shipping Free shipping is only available for orders shipped within the 48 contiguous United States. A shipping fee will be calculated and invoiced on orders shipping outside this area. The shipping fee must be paid before an order ships.

    MPPT-150-14.6 : 150W MPPT Solar Charge Controller for Lithium

    The Powerwerx MPPT-150-14.6, DC-to-DC Solar Charger Controller for Bioenno other 12V LiFePO4 Batteries. Rated at 150 watts, the MPPT-150-14.6 solar controller is designed for charging Bioenno 12V type LifePO4 batteries equivalent LFP batteries. This is a cost-effective controller for smaller single panel systems.

    Description

    The Powerwerx MPPT-150-14.6, DC-to-DC Solar Charger Controller for Bioenno other 12V LiFePO4 Batteries. Rated at 150 watts, the MPPT-150-14.6 solar controller is designed for charging Bioenno 12V type LifePO4 batteries equivalent LFP batteries. This is a cost-effective controller for smaller single panel systems.

    Input DC range from 16-25 VDC. Output is a constant 14.6 VDC. Rated at 12 Amps maximum. Smart charge controller design will automatically adjust charging output as required by batteries, no user adjustment needed.

    The Powerwerx MPPT-150-14.6 is a MPPT (maximum power point tracking) controller. This unit is rated at 150 watts and converts higher solar panel voltages down to 14.6 VDC which is more suitable for charging LifePO4 type batteries. The solar input is pre-wired with MC4 style connectors. The output comes pre-wired with the popular Anderson Powerpole 30A connectors.

    mppt, solar, charge, controller, li-ion, battery

    MPPT-150-14.6 Specifications:

    • Controller Technology: MPPT (Maximum Power Point Tracking) Technology
    • Input Voltage: 16-25 VDC
    • Output Voltage: 14.6 VDC
    • Input Connector Type: MC4
    • Output Connector Type: Anderson Powerpole 30A
    • Maximum Power: 150 Watts
    • Maximum Current: 12 Amps
    • Battery Type: Bioenno LiFePO4 or equivalent
    • System Type: 12 VDC (DC to DC converter)
    • Controls: Automatic (no user adjustments required)
    • Conversion Efficiency: 95%
    • IP Rating: IP67
    • Short Circuit Protection: Yes
    • Over Temperature Protection: Yes
    • Case: Die cast aluminum design allows for efficient heat dissipation
    • Dimensions: (L x W x H) 2.3 in. x 1.6 in. x 0.9 in. (58 mm x 40 mm x 22 mm)
    • Weight: 0.25 lbs. (115 g)
    • Warranty: 1 Year

    NOTE: This solar controller is intended for use with Bioenno LiFePO4 or equivalent batteries. This controller should not be used with Flooded, AGM or GEL type batteries as its voltage setpoints will overcharge them.

    Need to convert the output connector of this controller?

    The output connector is a 45A Anderson Power Pole. To convert to a 5.5×2.1mm DC barrel, use the BA-DCM-PP45 cable. To convert to a 5.5×2.1mm DC female jack, use the BA-DCF-PP45 cable.

    Victron BlueSolar MPPT 75/15 Solar Controller

    BlueSolar 75 VOC, 15 Amp MPPT solar panel charge controller for 12V and 24V battery systems including Lithium.

    SKU: VIC.SCC010015050R | MPN: SCC010015050R

    Available at Victron In Stock at Victrons Australian warehouse and typically ships within 5-6 Business Days.

    Recommended Accessories

    Shipping Included. 0.00 Delivery is typically 2 to 14 business days for In Stock items to Metro locations and longer for remote areas.

    Pickup from Southport Warehouse. 0.00 We will contact you via email when your order is ready for pickup. For items In Stock this is typically within 3 HOURS.

    Victron BlueSolar Controlles require the V.E.Direct Bluetooth Smart dongle. For in-built Bluetooth please view the SmartSolar range.

    MPPT controllers operate solar panels at their Maximum Power Point improving efficiency up to 30% by adjusting input voltage to harvest the maximum power from the solar panels. It then manages this power to supply the varying voltage requirement of the battery plus load.

    The Victron MPPT BlueSolar senses when to adjust the output that it is being sent to the battery and will shut down for a few microseconds, calculate and make relevant adjustments. The principle of MPPT is to extract the maximum possible power from a solar panel by setting the most efficient combination of voltage and current. maximum power point.

    The BlueSolar supports Advanced Maximum Power Point Detection. Unlike the conventional MPPTs which tend to lock to a local MPP when shady conditions occur, [which may not be the optimum MPP], Advance Maximum Power Point Detection will harvest maximum energy by locking to the optimum MPP. In addition the unit is configured for optimal Three Step Charging.

    With the V.E.Direct Bluetooth Smart dongle, programming, real-time data and history display is available on your Smart device.

    Inbuilt additional electronic protection provides

    Three Stage Charging

    • Stage One. Bulk or Boost. As much current as possible is delivered in order to rapidly recharge the batteries to about 80%.
    • Stage Two. Absorption. When the battery reaches its final charging voltage, known as its absorption voltage the charge allows the current to taper off as the battery nears a full charge.
    • Stage Three. Float. At this stage float voltage is applied which is enough to retain a full charge but controlled to prevent overcharging.

    MPPT 75/10, 75/15 MPPT 100/15 Specifications

    mppt, solar, charge, controller, li-ion, battery
    SKU VIC.SCC010015050R
    Model # SCC010015050R
    UPC/EAN 8719076025320
    Brand Victron Energy
    Shipping Weight 0.6840kg
    Shipping Width 0.210m
    Shipping Height 0.050m
    Shipping Length 0.150m
    Shipping Cubic 0.015750000m3

    Purchase with confidence knowing your product is covered by the Victron 5-year manufacturer warranty.

    Be The First To Review This Product!

    Help other Outback Marine Australia Pty Ltd users shop smarter by writing reviews for products you have purchased.

    Related products

    Same Day Dispatch (Order by 1PM)

    Authorised Victron Repair Centre

    SIGNUP and SAVE!Join the CLUB for news and special member-only pricing, promotions and offers. It’s FREE to Join

    © 2023 Outback Marine Australia Pty Ltd. ABN: 26082231892. All rights reserved.

    Terms Conditions

    Welcome to our website. If you continue to browse and use this website, you are agreeing to comply with and be bound by the following terms and conditions of use, which together with our privacy policy govern Outback Marine Australia Pty Ltd’s relationship with you in relation to this website. If you disagree with any part of these terms and conditions, please do not use our website.

    The term ‘Outback Marine Australia Pty Ltd’ or ‘us’ or ‘we’ refers to the owner of the website whose registered office is. Our ABN is 26082231892. The term ‘you’ refers to the user or viewer of our website.

    The use of this website is subject to the following terms of use:

    • The content of the pages of this website is for your general information and use only. It is subject to change without notice.
    • Neither we nor any third parties provide any warranty or guarantee as to the accuracy, timeliness, performance, completeness or suitability of the information and materials found or offered on this website for any particular purpose. You acknowledge that such information and materials may contain inaccuracies or errors and we expressly exclude liability for any such inaccuracies or errors to the fullest extent permitted by law.
    • Your use of any information or materials on this website is entirely at your own risk, for which we shall not be liable. It shall be your own responsibility to ensure that any products, services or information available through this website meet your specific requirements.
    • This website contains material which is owned by or licensed to us. This material includes, but is not limited to, the design, layout, look, appearance and graphics. Reproduction is prohibited other than in accordance with the copyright notice, which forms part of these terms and conditions.
    • All trademarks reproduced in this website, which are not the property of, or licensed to the operator, are acknowledged on the website.
    • Unauthorised use of this website may give rise to a claim for damages and/or be a criminal offence.
    • From time to time, this website may also include links to other websites. These links are provided for your convenience to provide further information. They do not signify that we endorse the website(s). We have no responsibility for the content of the linked website(s).
    • Your use of this website and any dispute arising out of such use of the website is subject to the laws of Queensland Australia.

    Privacy Policy

    This privacy policy sets out how we uses and protects any information that you give us when you use this website.

    We are committed to ensuring that your privacy is protected. Should we ask you to provide certain information by which you can be identified when using this website, then you can be assured that it will only be used in accordance with this privacy statement.

    We may change this policy from time to time by updating this page. You should check this page from time to time to ensure that you are happy with any changes.

    What we collect

    We may collect the following information:

    • name and job title
    • contact information including email address
    • demographic information such as postcode, preferences and interests
    • other information relevant to customer surveys and/or offers

    What we do with the information we gather

    We require this information to understand your needs and provide you with a better service, and in particular for the following reasons:

    • Internal record keeping.
    • We may use the information to improve our products and services.
    • We may periodically send promotional emails about new products, special offers or other information which we think you may find interesting using the email address which you have provided.
    • From time to time, we may also use your information to contact you for market research purposes. We may contact you by email, phone, fax or mail. We may use the information to customise the website according to your interests.

    We are committed to ensuring that your information is secure. In order to prevent unauthorised access or disclosure, we have put in place suitable physical, electronic and managerial procedures to safeguard and secure the information we collect online.

    How we use cookies

    A cookie is a small file which asks permission to be placed on your computer’s hard drive. Once you agree, the file is added and the cookie helps analyse web traffic or lets you know when you visit a particular site. Cookies allow web applications to respond to you as an individual. The web application can tailor its operations to your needs, likes and dislikes by gathering and remembering information about your preferences.

    We use traffic log cookies to identify which pages are being used. This helps us analyse data about webpage traffic and improve our website in order to tailor it to customer needs. We only use this information for statistical analysis purposes and then the data is removed from the system. Overall, cookies help us provide you with a better website by enabling us to monitor which pages you find useful and which you do not. A cookie in no way gives us access to your computer or any information about you, other than the data you choose to share with us. You can choose to accept or decline cookies. Most web browsers automatically accept cookies, but you can usually modify your browser setting to decline cookies if you prefer. This may prevent you from taking full advantage of the website.

    Links to other websites

    Our website may contain links to other websites of interest. However, once you have used these links to leave our site, you should note that we do not have any control over that other website. Therefore, we cannot be responsible for the protection and privacy of any information which you provide whilst visiting such sites and such sites are not governed by this privacy statement. You should exercise caution and look at the privacy statement applicable to the website in question.

    Controlling your personal information

    You may choose to restrict the collection or use of your personal information in the following ways:

    • whenever you are asked to fill in a form on the website, look for the box that you can click to indicate that you do not want the information to be used by anybody for direct marketing purposes
    • if you have previously agreed to us using your personal information for direct marketing purposes, you may change your mind at any time by writing to or emailing us.

    We will not sell, distribute or lease your personal information to third parties unless we have your permission or are required by law to do so. We may use your personal information to send you promotional information about third parties which we think you may find interesting if you tell us that you wish this to happen.

    If you believe that any information we are holding on you is incorrect or incomplete, please write to or email us as soon as possible at the above address. We will promptly correct any information found to be incorrect.

    Leave a Reply

    Your email address will not be published. Required fields are marked *