Skip to content
200KW 250KW 492VDC off grid inverter. 250kw solar panel cost

200KW 250KW 492VDC off grid inverter. 250kw solar panel cost

    How Much Solar Power Do I Need?

    My advice on solar power system sizing has changed over the years due to the cost of solar panels continuing to reduce over time.

    This video explains the system size providing the best bang for buck for the typical Australian household:

    Spoiler alert – if you don’t feel like watching, my advice on system sizing is: “if you have reasonable electricity consumption and a decent feed-in tariff, install as many solar panels as you can fit and afford.”

    This article digs a bit deeper into why my advice is to ‘fill your roof’ rather than a specific size and shows how to use my nifty solar calculator to see what a solar system can do to your bills.

    The size of a solar power system is described by total panel capacity, expressed in kiloWatts (kW).

    A Watt is a basic measure of electrical power, and the kilo means there are 1000 of them. i.e. 1 kW = 1000 Watts

    200kw, 250kw, 492vdc, grid, inverter

    For example – a system made up of 16 x 415W solar panels = a 6.6 kW system.

    When buying a solar power system, it’s common for installers to quote on ‘oversized’ systems.

    The linked article goes into more detail, but in short – you get huge bang for buck by putting on 33% more panels than an inverter is rated for.

    This is why 6.6kW solar systems, using 5 kW inverters, are still very popular in 2023 – they represent a sizing ‘sweet spot’ for what the typical home can fit on the roof. They’re also usually the maximum size a Distributed Network Service Provider (DNSP) will allow on a single-phase home (more on DNSPs below).

    Note when you have an ‘oversized’ system, you will never produce more power than what the inverter is rated for. For example, a 6.6 kW solar system using a 5 kW inverter will never produce more than 5 kW at any given point in time.

    People assume this would result in ‘lost’ energy generation due to ‘clipping’ of production at 5 kW, but averaged over a year you lose little – so don’t stress.

    A word of caution: Be sure to understand what an installer is quoting you on. Make sure it is the solar PV peak Watts and NOT the inverter size they are quoting. In the past, I’ve seen advertising selling a “10 kW system” consisting of a 10 kW inverter with only 8 kW of solar panels!

    To give you a feel for the amount of power a kiloWatt represents, the table below shows what you can run with 1 kW of power:

    Wow, so could you power 60 globes with a 1 kW solar power system? Kind of.

    A 1 kW solar panel system will only produce 1 kW of power for a few hours a day, and then only if it is a clear, sunny day. So your 60 globes will only be all on for a few hours a day.

    The graph below shows what the electricity output of a 1 kW solar power system might look like over a summer’s day. You can see 1 kW is only generated at midday when the sun is at its strongest:

    This is the reason most solar systems are connected to the mains electricity grid. The grid will absorb any electricity generated by the solar panels not used by your home. When you are using more electricity than can be produced by the sun (and at night, of course), the grid automatically tops up your electricity needs.

    How many solar panels will you need to offset your electricity usage?

    First – I want to address most people’s motivation for going solar: “I want to put on solar panels and get my electricity bill to zero!”

    Getting a zero dollar bill isn’t as simple as installing enough solar panels to generate whatever your average daily usage is. As I explained previously, when you use electricity is almost as important as the amount of electricity you use. This is because a solar system only generates its maximum at midday on a ‘good’ day.

    Solar power, regardless of system size, won’t do much to a massive electricity bill if it’s all caused by overnight air-conditioner usage!

    Getting zero bills with only solar panels – and no battery storage – is possible. Until I added an electric car to my home, I regularly got credits on my electricity bills.

    Yup – my retailer was paying me for the privilege of being connected to the electricity network!

    But – for those of you with sky-high energy costs and not enough room for a huge solar power system, it’s important to FOCUS on the amount solar energy can reduce your bills by, not whether or not it can simply get your bills to 0.

    Or, to put it another way – if solar power could take your 500 quarterly bill down to 50, would you be annoyed you didn’t get your fabled ‘0 bill’, or would you be jumping for joy your solar system saved you 450 in 3 months?

    Now – let’s get into some hard numbers on system sizes with the help of my nifty solar calculator.

    Example for a typical home in Sydney

    Let’s take a home in Sydney with 500 quarterly electricity bills, paying 0.29 per kWh for grid electricity and gets paid a 0.12 per kWh feed-in tariff. They paid 5,500 for a north-facing 6.6 kW solar system and have 25% solar electricity self-consumption.

    Putting these assumptions into my calculator yields the following result:

    1,585 in electricity bill savings in the first year! Not too shabby.

    Or, to look at it from the perspective of “What will my electricity bills be before/after solar?”:

    A 9 spring electricity bill! Most homeowners would be thrilled.

    So – a 6.6 kW system in Sydney, assuming 25% solar energy self-consumption, won’t quite get a 500 quarterly bill to 0 – but it gets close!

    If this home could fit more than 6.6kW on their roof – closer to 10kW total – with the same consumption patterns they’d be in credit year-round.

    What roadblocks are there to filling your roof with solar panels?

    Besides the obvious (physical roof size/space and your budget), the other obstacle preventing you from maxing out your roof with panels are limitations set by your “Distributed Network Service Provider”, or DNSP.

    But, to use an example, here in South Australia, SA Power Networks (SAPN) is our only DNSP.

    They have set system size limits of:

    • Single-phase homes: 10 kW inverter limit, 5 kW export limit.
    • Three-phase homes: 30 kW inverter limit, 15 kW export limit.

    Meaning – if you have a single-phase home in SA, you could have up to 13.3 kW of solar panels on your roof with a 10 kW inverter. Remember – you can oversize an inverter by 33%. But – you’d be export limited to 5 kW

    Export limitations mean your inverter will intelligently ramp down solar power production to ensure a maximum of 5 kW is sent to the grid at any one time.

    Some homeowners ask me “If my energy needs are low-to-moderate, isn’t it pointless to install a large system if I’m export limited?”

    The answer, surprisingly, is no. You lose less generation than you’d expect with export limitation due to a variety of factors.

    Why bigger is better, even if you believe you won’t need a larger system

    Even with feed-in tariffs dropping and export limitations for single phase homes in certain states, maxing out your roof with solar panels is a Smart move for two reasons:

    • Winter and summer are typically the highest energy usage seasons for households. But in summer, solar power systems pump out a ton of energy, so they can help offset big electricity bills easily. In winter, your solar energy generation can be less than half of what it is in summer, so big winter bills are harder to offset unless you have a larger solar system (10 kW or more).
    • Future-proofing. I believe by 2030 many homes will have battery storage and electric cars.

    Batteries and electric cars need lots of solar generation to reliably charge, and then you need more solar electricity to offset the energy needs of the rest of your home.

    I recently installed more solar panels on my south-facing roof (which some installers refuse to install on!) because my home now has two electric cars and a Tesla Powerwall battery. My previous 6kW system struggled to generate enough energy for them all.

    I’ll finish by saying – while I regularly hear from homeowners who wish they put on more solar panels when they had the chance (because it’s expensive and a technical headache to add panels to an existing system), I have never heard anyone complain they’ve installed too much solar power.

    0KW 250KW 492VDC off grid inverter

    This low frequency inverter used for large power factory, hospital, school,etc. It has huge transformers inside can suffer large current and votlage. All inverter is true power rate will not use fake components to reduce any cost.To get the most out of the power inverter, it must be installed and used properly.

    • item no.: SWI-200kw
    • lead time: 7
    • product orgin: China
    • shipping port: china
    • color: white black

    200KW 250KW 492VDC off grid inverter

    200KW 250KW 492VDC off grid inverter features

    This low frequency inverter used for large power home load or machines. It has huge transformers inside can suffer large current and votlage. All inverter is true power rate will not use fake components to reduce any cost.To get the most out of the power inverter, it must be installed and used properly.

    l Using the fifth efficient IPM power module from Mitsubishi

    l High conversion efficiency, Max. Efficiency≥88%

    l Perfect protection and warning functions

    l Low Frequency Transformer, which ensures that inverter has high efficiency and low no-load loss

    l Pure sine wave output, has higher efficiency and higher capability of driving load

    l LCD display, high efficiency, easy installation

    Compliant with European Standards (CE)

    RoHS compliant

    Made in China

    Produce of off grid solar power inverter

    off grid solar power inverter

    15KW 192V off grid solar power inverter

    15KW inverter can make singple phase and three phase output voltage. It has huge transformers inside can suffer large current and votlage. All inverter is true power rate will not use fake components to reduce any cost.To get the most out of the power inverter, it must be installed and used properly.

    1KW off grid solar inverter

    This low frequency inverter used for large power home load or machines. It has huge transformers inside can suffer large current and votlage. All inverter is true power rate will not use fake components to reduce any cost.To get the most out of the power inverter, it must be installed and used properly.

    2KW solar inverter for off grid system

    This low frequency inverter used for large power home load or machines. It has huge transformers inside can suffer large current and votlage. All inverter is true power rate will not use fake components to reduce any cost.To get the most out of the power inverter, it must be installed and used properly.

    5KW solar off grid power inverter

    This low frequency inverter used for large power home load or machines. It has huge transformers inside can suffer large current and votlage. All inverter is true power rate will not use fake components to reduce any cost.To get the most out of the power inverter, it must be installed and used properly.

    3KW solar off grid power inverter

    This low frequency inverter used for large power home load or machines. It has huge transformers inside can suffer large current and votlage. All inverter is true power rate will not use fake components to reduce any cost.To get the most out of the power inverter, it must be installed and used properly.

    10KW 96V off grid solar inverter

    10KW inverter is low frequency inverter used for large power home load or machines. It has huge transformers inside can suffer large current and votlage.

    • Solar Panel
    • Mono Solar panels
    • Poly solar panels
    • Dual glass solar panels
    • Solar power system
    • Off grid solar system
    • On grid solar system
    • MPPT solar charge controller
    • PWM charge controller 1-70KW
    • Wind charge controller

    Hefei Sunway Power Co.,Ltd. located in APEC High-Tech Industrial Park, Hefei National Hi-Tech Industrial Development Zone, is a professional and high-tech enterprise that engaged in wind generation, photovoltaic system and other renewable energy RD, manufacturing and marketing.

    Sunway power main products are PV solar system, portable solar system, Solar panels, MPPT solar and wind controller series, PV and wind system controller series, solar inverter. Our products had many intellectual property, and gained 12 national patents, software copyright certificate, passed the testing from national testing organization and CE Certification Institution. Also we have registered brand successfully. Our company has been rated Hi-tech Enterprise and gained ISO-9001certificate since August, 2011 year.

    Our unique design and superior performance win highly praise and trust from our clients. We supply products for wind turbine manufactures with so many years, export to developed countries including Germany, Italy, England, Russia, Australia, USA, Canada, Spain, as well as Middle East and Southeast Asia.

    Our Certificate

    Our Patents

    • No 767 Yulan Road, National High-Tech Industrial Development Zone, Hefei City, Anhui Pro., P.R of China
    • mob/whatsapp/wechat: 008618605560996
    • email: sales@sunway-power.com
    • skype: kevinfkyan

    Editors Note: This is an overview on how to understand how much energy your solar system will produce and overall solar panel output.

    We always advise speaking with at least a few certified solar installers to understand how all the factors will affect solar panel output for your system.

    Solar panels indicate how much power they intend to produce under ideal conditions, otherwise known as the maximum power rating.

    But how much electricity your solar panels produce depends on several factors.

    • Does intermittent shading obscure direct sunlight from hitting the roof?
    • How much sunlight does your roof get on average?
    • How big are the solar panels, and how efficient are the solar cells at converting energy?

    Because the seasons and weather conditions affect the amount of sunlight hitting your roof, and the amount of sunlight also varies on the time day, you can’t use just the solar panel ratings to predict how much power you’ll get. However, your location will allow you to do some math and determine how well a solar panel works where you are.

    How Much Power Am I Using?

    A kilowatt-hour is a basic unit of energy, which is equal to power (1000 watts) times time (hour). Your electric bills show how the average number of kWh you use per month.

    For example, a 50 Watt light bulb left on for one hour would be 50 Watt hours, and 20 50 watt light bulbs running for one hour would be 1 kilowatt-hour (kWh). According to the U.S. Energy Information Administration, the average monthly electricity consumption for a residential utility customer is about 903 kWh per month.

    Divide your average monthly usage by 30 days in a month to get your daily usage. If you’re going by the national average, then you should be using about 30 kWh per day. Next, figure out the average amount of sunlight you get per day. The US ranges from about 4 hours – 6 hours of sunlight per day, on average, see the below map. Let’s estimate you get about five hours per day to generate that 30 kWh you use. So the kWh divided by the hours of sun equals the kW needed. Or, 30 kWh / 5 hours of sun = 6 kW of AC output needed to cover 100% of your energy usage.

    How much solar power do I need (solar panel kWh)?

    This depends in part on the amount of electricity you want to offset with solar power as well as the question ‘how much energy does a solar panel produce’, so in order to get more specific let’s talk about the actual number of solar panels.

    How many solar panels do I need then?

    Typically, a modern solar panel produces between 250 to 270 watts of peak power (e.g. 250Wp DC) in controlled conditions. This is called the ‘nameplate rating’, and solar panel wattage varies based on the size and efficiency of your panel. There are plenty of solar calculators, and the brand of solar system you choose probably offers one. That said, there is a simple equation to calculate the amount of kilowatt-hours (kWh) your solar panel system will produce.

    So now that we know you need to produce about 6kW of AC output, we can work backwards to figure out how many solar panels you need. Solar panels produce direct current (DC), and your home runs on alternating current (AC).

    Because of physics, there are losses in converting the energy from the sun into DC power, and turning the DC power into AC power. This ratio of AC to DC is called the ‘derate factor’, and is typically about.8. This means you convert about 80% of the DC power into AC power.

    This continues to improve ever so slightly, but the losses are unavoidable… because of physics! So you take the AC amount you need: 6kW and divide by.8 (6kW/.8 = 7.5kW DC). This means that you’ll need 30 250Wp solar panels or 27-28 270Wp panels.

    By NREL [Public domain], via Wikimedia Commons

    200kw, 250kw, 492vdc, grid, inverter

    How much do I save?

    Finally, let’s find out how much you can save per month on average from your monthly electric bill!

    Let’s plug it all in:

    On average, your solar system is going to lose some energy due to wiring, power, inverter efficiency, so you actually end up using 80% of your solar system’s capacity.

    To figure out how many kilowatt-hours (kWh) your solar panel system puts out per year, you need to multiply the size of your system in kW DC times the.8 derate factor times the number of hours of sun. So if you have a 7.5 kW DC system working an average of 5 hours per day, 365 days a year, it’ll result in 10,950 kWh in a year.

    If you divide your expected 10,950 kWh of annual production by 12, you’ll see that your system will offset about 912 kWh per month from your monthly electric bill, which can translate to 100 or more (in California this would save you about 250) per month depending on how much you pay per kWh!

    So to break this down into simple math that you can do:

    AC rating = Average kWh per month / 30 days / average sun hours per day

    example: 903 kWh per month / 30 days / 5 hours = 6.02 kW AC

    DC rating = AC rating / derate factor (.8 is conservative, but a range would be.8 –.85)

    example: 6.02 kW AC /.8 = 7.53 kW DC

    Number of panels = DC rating / Panel Rating (e.g. 25o W) note this is important b/c panels are rated in watts, and the systems are rated in kilowatts (1000 watts). So a 7.53 kW system = 7530 Watts and a 250 watt panel =.250 kW

    example: 7.53 kW x 1000 / 250 watt = 30.12 panels, so roughly 30 250 panels (30 x 250W = 7500 Watts = 7.5 kW)

    NOTE: to get your average usage, preferably add up your last 12 months usage and divide by 12. In a pinch, the last 6 months can be a close approximation, but a year’s worth of data is far better.

    200kw, 250kw, 492vdc, grid, inverter

    Have you calculated how much your solar system will produce? Tell us in the Комментарии и мнения владельцев!

    200kw, 250kw, 492vdc, grid, inverter

    Commercial properties and agricultural buildings require a significant amount of electricity to operate, which can be a major overhead for any business and affect its profitability.

    These buildings and properties provide large, uncomplicated roof space which is ideal for a rooftop solar PV system and today, businesses are able to reduce their energy bills significantly with solar PV.

    In the table below, we compare solar PV systems installed by Mypower between 2012 and 2021. Each system is of a similar size (100 kW) producing around 91,500 units p.a, using panels with a 25-year warranty and inverters with a 10-year warranty. The figures are based on 60% of the solar generated electricity being used on site by the businesses. With grid electricity supplied rising and a fall in supply and installation costs, it means that ROI and payback have improved.

    NB: These are year 1 figures, the FiT increases by RPI and the Savings by electricity inflation. currently around 7%, improving ROI in future years.

    The reduction in the FiT subsidy to zero over the years is offset by the increased efficiency of the panels, reduced cost of the system and significantly increased grid electricity costs. Ben Harrison MRICS, who heads up solar installers Mypower, explained: “The saving between grid and solar electricity, including operating and maintenance costs, is now more than 5 times what it was in 2012, which is why FiT subsidy is no longer required. The cost of a solar PV system is 50% less than it was in 2012, making it available to more businesses as an affordable investment.”

    Will electricity continue to rise?

    Energy experts have carried out extensive research on the future of non-commodity costs within an electricity bill, and their workings show that these costs alone are set to increase over the next five years. This means that even if the wholesale electricity cost remains static, bills will increase by 33% in the next 5 years!

    Ben also outlined: “With such dramatic electricity price increases, solar is no longer about payback or ROI, it’s about being in control of your own supply of electricity at a price around 70% less than grid electricity.

    “For those who still measure everything in payback time, remember the panels are warranted for 25 years. That’s payback of 2 years on equipment lasting 5 years with 3 years of “free” production, or solar with a payback of 7 years and 18 years of “free” production.”

    The graph below depicts a projected rise in charges that you can expect to see on your business’ electricity bill:

    What are non-commodity costs?

    The unit rate on your electricity bill, while not usually broken down on the bill, is divided into two main elements. the wholesale costs of electricity (the commodity) and non-commodity costs. Although there are regular fluctuations in the electricity markets, the split between commodity and non-commodity costs is approximately 50:50. Non-commodity costs include governement levies, tarrifs and third party charges. The chart below provides an indicative illustration of the typical costs.

    Why the increase?

    As you may be aware, the UK’s electricity infrastructure is strained and the network (National Grid) is being pushed to capacity. This, combined with a global push to reduce emissions and energy consumption in general, means that you will see an increase in taxes and charges and will pay more for delivering electricity to your premises via the network.

    What does this mean for businesses looking to install solar?

    Businesses like predictability, especially when it comes to purchasing inputs. With solar, you can forward-buy a significant chunk of your next 25 years’ worth of input at a fixed price of around a third of what you currently pay. It won’t go up, you have no storage costs and, if you ever decide you don’t need any of it, you get your money back (export to the grid). How many businesses would like to buy all their inputs like this?

    Solar power is a cost-effective, low maintenance and reliable supply of energy which is protected against price rises and works alongside grid supplied electricity. Average payback length is 5-6 years and a solar investment can be cash flow positive in as little as 2 years. With low interest rates and additional tax benefits, solar is therefore viewed as a low risk investment.

    Ben Harrison explained: “Matching the daytime generation from the panels to the electricity demand from the building is the most efficient way to use solar. The energy produced on site is actually used at the premises, meaning that the business needs to import less energy from the grid. Quality solar panels are guaranteed to deliver a 25-year linear power output which means businesses can accurately predict the cost they will pay for each unit of electricity for the next 25 years. The lifetime of solar panels are estimated to be much longer, at around 40 years. A 50kW solar PV system using 70% of the generation on site can expect a projected first year income and savings of £5,700, giving a first year return on capital of 18% before indexation. Any unused energy can be sold back to the National grid.”

    Monssi – 70kW solar PV system install by Mypower

    There can be additional tax benefits. Solar systems are classed as plant and machinery, so can be eligible for capital allowances. i.e for the capital cost to be written off against profits in the first year. In such a case, a farming partnership paying 40% tax can often claim back from HMRC 40% of the cost of the solar installation in their next tax return. This can mean a £45,000 investment effectively costs the business just £27,000, making the first year return on capital significantly higher at around 28% with a 3-year pay back, and the cost of producing electricity significantly lower, at around 3p per unit.

    In addition to all the financial benefits, a business can significantly reduce its carbon footprint. Some businesses have won major contracts assisted by the added “green credentials” gained after installing solar panels, while others have reduced their carbon footprint to help maintain existing business relationships. A 50 kW solar PV system will help a business to reduce its CO2 emissions by over 20 tonnes per annum. They can also promote their environmental saving contributions in marketing literature and a display screen onsite.

    Generating your own energy is the future. By 2025 the Government are planning to close all coal fire power stations. With solar power becoming the cheapest form of electricity, combined with today’s low interest rates to finance an installation, now is the time for your business to invest in solar.

    Delaney Mackay Lewis Ltd. Commercial Landlord

    Goodridge Business Park is home to a number of commercial units owned by Delaney Mackay Lewis Ltd. As a part of their refurbishment programme, Delaney Mackay Lewis were looking to make the site attractive to potential tenants. This included improving the site’s environmental credentials with a 250kW Solar PV system.

    Far Peak Eco Park. Gloucestershire

    Far Peak Business Park is located near Northleach. Mypower designed and installed a 49.83kWp, making maximum use of the available roof space. Utilising the 30% grant available (saving £11K) in Gloucestershire, Far Peak will achieve an 22.8% ROI

    About Mypower

    Mypower are a highly experienced award winning team who consult, design, supply and install solar PV for agricultural and commercial solar panel clients. We work with companies to help them significantly reduce their electricity bills, secure their energy, future-proof their electricity costs and reduce their carbon footprint. Delivering quality work with the highest customer service is at the heart of our business. The solar PV panels we install are high yielding, very efficient and award-winning, so our customers achieve the maximum production and returns from their solar installation. In addition, we work with consultants to renegotiate each customer’s electricity price with their suppliers as a free-of-charge service.

    For more information and friendly, helpful advice

    Keep track on what we’ve been up to and join the conversation on clean, green, renewable energy on our LinkedIn, Instagram, and !

    • General Information
    • About us
    • Careers
    • Privacy and cookie policy
    • Site map
    • Sectors
    • Agriculture
    • Commercial
    • Industrial
    • Services
    • Solar Panel Cleaning
    • Solar PV Monitoring

    Kehua 250kW solar inverter for a solar farm

    Review of the Pros and cons of Kehua 250kw solar inverter. Advantages of using HJT solar panels and Kehua Tech solutions for utility-scale.

    Discover the Kehua 250kW Intelligent String Inverter

    Kehua Tech is a producer of business solutions for photovoltaics, energy storage and data centers. After successes in China, the USA and India, it was Poland that became the key market for Kehua. The presence of this global company in Poland consists mainly of photovoltaic installations for companies, farmers and photovoltaic farms. And the flagship solution is a 250kW inverter.

    Thanks to the combination of advanced technology from data centers in which artificial intelligence is the leader and industrial solutions of the nuclear class, an inverter with a power of 250 kW were created. The Kehua SPI 250k inverter is probably the most modern and reliable inverter of this type in the world. It is ideal for photovoltaic farms with nominal power from 1mW to even 100mW, divided into photovoltaic blocks.

    Why Kehua SPI Inverter 250K?

    The reliability of the 250kW inverter is confirmed by the applied solutions such as:

    • IP66 and key components such as IP68 cooling
    • AFCI with active intelligent arc detection
    • Industry’s first self-extinguishing fire protection system
    • Corrosion class C5
    • Resistance to salt mist and operation in conditions of high humidity
    • Best Match with N-type Panels like Jolywood, AKCOME,Jinergy and Risen

    Compatibility with Bifacial modules and high power above 400W. 250KW Inverter

    Each string max 15A / DC Input Power 1500V / High DC-AC ratio

    Efficiency and reliability 250KW inverter

    24 inputs / 12MPPT / 99% Efficiency / PID resistance repair / SCR

    Bifacial Modules Double Savings in an Inventory of 250KW

    By using Bifacial photovoltaic modules, which are usually additionally made in Glass Glass technology, it generates up to 20% more power. At the same price, an investor in a solar farm receives an additional value. The degradation of double-glass modules is always lower than that of standard PV modules, made in the back sheet technology. Therefore, the modern design of Kehua 250 kW supports all bifacial panels available on the market.

    MPPT trackers versus savings and efficiency in Solar Inverter 250KW

    When supporting high-power modules ( 400W) and bifacial photovoltaic panels, the current strength on individual strings and the entire MPPT optimizer should be taken into account. KEHUA solved the problem of high voltage and current by increasing the MPPT number of trackers to 12 and the number of strings to 24. And thanks to the current of 30 A, it is possible to optimally design large-power photovoltaic installations without fear of exceeding the permissible short-circuit current of photovoltaic modules.

    Safety of the KEHUA 250k Inverter and AFCI on PV farms

    Detection of electric arcs is the most modern solution for business and investment projects such as solar farms. If a DC cable is broken, the dangerous phenomenon of a DC electric arc is created. High temperature accompanying this phenomenon may cause a fire hazard and damage the entire investment. The answer from the Kehua 250kW Inverter is an artificial intelligence-based arc detection and interruption system. Within a few ms, the inverter detects the electric arc via the AFCI function and interrupts it. It also transmits remote information about the occurrence of this phenomenon and an immediate need for service, which is guaranteed by Energia Pomorze. Kehua additionally supports bifacial double-glass modules, so that apart from AFCI, the glass in the back of the module provides protection against fire.

    When an arcing occurs, AFCI analyzes the characteristics of the event and determines whether it is a hazardous event. AFCI manufacturers test hundreds of possible operating conditions and then program their equipment to continuously monitor normal and hazardous arc conditions.

    Against Fire System for Photovoltaic Farm

    The fire protection solution used in the 250kW Inverter makes the inverter react automatically when a short circuit occurs and a fire occurs. This ensures the highest level of security and reliability characteristic of all KEHUA products.

    DC and AC KEHUA Energy Storage

    Thanks to Kehua’s comprehensive approach and production capabilities, business customers get a ready-made solution for large-capacity energy banks. The 250kW inverter is compatible with all types of power banks, whether DC or AC. This solution makes the Kehua inverter suitable for investments where the power of the photovoltaic installation is provided only for own needs and the surplus energy is stored in batteries. This is related, for example, to the lack of connection capacity in the investment location and requires very precise planning and control of the installation. In a DC / DC current production and storage solution, the Kehua250k inverter reduces costs and improves the operation of the entire ESS system.

    In addition, Kehua SPI 250k inverters have the ability to participate in auxiliary services on the grid side, such as:

    P / F Basic frequency control2. Q / V Primary voltage regulation3. SPF Dynamic power factor control4. PF Steady-state power factor control5. SVG night6. Constant power regulation7. Compensation of reactive power

    The best-made 250KW Inverter for Solar Farms?

    Kehua 250 kW is not only about advanced technology inside the device and fire protection systems. The Kehua inverter is also characterized by the highest quality workmanship, thanks to which it can be used in the most demanding working conditions. The main features of perfect execution are:

    – Standard IP 66 and the most important elements such as the IP68 cooling system

    – The highest corrosion resistance class C5, allowing for operation in the industrial and marine environment

    – The applied sealants and silicone rubber sealing ring use the latest technologies used in the industry

    – Aluminum alloy housing guarantees long operation in all conditions

    – Perfect Match with high power Heterpjunction and N-Type panels

    The technologies for processing the casing and design protection of the 250kW inverter are the result of Kehua Tech’s experience in the construction of a nuclear power plant and traditional power plants as well as those based on renewable energy sources such as hydroelectric power plants, wind power plants and solar power plants.

    Leave a Reply

    Your email address will not be published. Required fields are marked *